Now go to System >Advanced > Miscellaneous and scroll down to Gateway Monitoring. Go ahead and confirm its listed, and click saveĪnd you should now see an extra gateway listed Now you should have a gateway listed on the interface. I do not recommend this.Įnter a gateway name, and then again enter the IP address we were given by Mullvad, and hit add This could be what you want though, so if it is, check it. If it is checked, it will send all traffic over this gateway by default. Here you will yet again enter the IP you were given by Mullvad, along with the network mask of /32Ī new screen will show, make sure Default Gateway is unchecked. Set the IP configuration for Static IPV4 and scroll down to the Static IPV4 configuration. You want to make sure its enabled, give it a better name like Mullvad_WG or whatever you like Now go ahead and edit the interface we just created which has tun_wg0 as the port selection You will now have one called tun_wg0 in there. Now the setup in Wireguard is complete, we just need to set up some more things in PFSENSEĪt the bottom of the screen you will see a dropdown for Available network ports. Lastly, enter 0.0.0.0 with a netmask of 0 in the address configurations, and then hit save It defaults to 51820 which is the correct port, and paste in the public key from the server selection screen Go ahead and enter the server, and you can leave the port blank. This will give you the fields to enter the server details Give it a description, and uncheck dynamic endpoint. Now go back to PFSENSE, make sure Enable Peer is enabled and make sure the Tunnel is listing the tunnel we created earlier ( Note, if you later want to change server, you need to update both of these fields with the new server information) Don't confuse the public key with your own you generated earlier. If the name is us235-wireguard then the hostname is. go to the below linkĪnd filter for Wireguard, and your location, or wherever you want. Now you'll want to decide what server you want to connect to. Now go into the Tunnel you created, and click add peer Now head back to the PFSENSE Window with the Tunnel configruation, and add that IPv4 address and subnet mask into the Interface Address, give it a name and hit Save Tunnel That's all, you can close the window now. Substitute the 000's for your account number with no spaces, and paste the public key we generated in PFSENSE earlier. You'll want to paste the below in Notepad and get it set up, then paste into the PFSENSE ShellĬurl -d account=0000000 -data-urlencode pubkey=YOURKEYHERE This isn't really a great idea, and this way is better. You can do this via the browser, but as /u/Griffo_au on reddit pointed out, you need to upload your private key. So if nothing else, just SSH to PFSENSE and follow these steps. I did it on my Mac, but your PFSENSE box also does. ![]() Do this from any system that has curl on it. Now we need to upload this key to Mullvad in order to get back the IP addresses we can use. Leave the port as default and click generate under the interface key.Ĭopy this key to a a notepad (Or whatever you like) as we will need it later. Now in the top bar, go to VPN > Wireguard > Settings and make sure its enabledĬlick to enable the tunnel, enter a name, it can be anything you like. If you don't, just click "Available Packages" and search for Wireguard, and install it. Go to System > Package Manager and make sure you have Wireguard installed Note that you should keep your account number secret. Save your account number, and pay for the plan. So I looked over 4 or 5 guides on how to set it up, and wrote this including screenshots, to make it easy.įirst click the above link, or just go to and sign up for an account. I could not find a complete guide on how to get PFSENSE connected to Mullvad with Wireguard. Using WireGuard if PFSENSE I get full line speed with very low CPU Usage on the firewall.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |